When somebody calls about an electrical problem in Exeter, the first thing that happens is a real conversation about what is going on. Not a form submission and a callback window. A call where the person on the other end knows the trade, can scope the job on the phone, and gives you the price before anything is scheduled. That is how every visit starts, whether it is a tripping breaker in a colonial on a quiet street or a panel that has run out of room in a rental unit.
Exeter is a town with a meaningful share of older housing stock, and older homes carry wiring decisions made under different standards, panels sized for lighter loads, and circuits that have been added to over the years without always being documented. We handle the full range of residential and commercial electrical work here, from a single outlet replacement to a full panel upgrade or generator hookup. Working here means getting the diagnosis right before the work starts.
The visit begins at the panel. Before any repair or installation work is touched, we look at what the circuit is doing, where the fault sits, and whether the panel itself is part of the picture. That sequence matters because a symptom at an outlet or a fixture often has a cause somewhere else in the circuit, and chasing the symptom without tracing the cause leads to a repair that does not hold.
We explain what we find before we proceed. That means a plain description of the problem, what it takes to fix it, and whether there is anything else in the panel or the wiring that affects the job. Straight answers about your panel and wiring are part of every visit, not something you have to ask for. We are built around that approach, and it is what the call reflects before anyone comes to the door.
An outlet that stops working, a switch that no longer controls the right fixture, a receptacle that needs to move for a renovation - these are the calls that come in most often, and the fix depends on what the circuit behind the outlet is actually doing. We replace standard outlets, install GFCI receptacles in kitchens, bathrooms, and exterior locations, and handle AFCI outlets in bedrooms where arc-fault protection is part of the current code requirement. Dimmer switches, three-way switching, and USB outlets all fall in the same category.
A generator sitting in a garage is not useful until it is properly connected to the panel. The connection requires a transfer switch, which isolates the generator from the utility grid so it cannot backfeed live power onto lines that workers may be on during an outage. We handle the transfer switch installation, the dedicated circuit from the panel to the generator connection point, and the load calculation that determines which circuits the generator feeds. In this part of New England, where multi-day outages in winter are not unusual, that wiring is practical rather than precautionary.
A welder or an air compressor draws a load that a standard household circuit cannot carry reliably. Running a dedicated circuit sized to the equipment protects both the equipment and the panel from the kind of nuisance tripping and voltage drop that comes from sharing a circuit with other loads. We scope the amperage requirement on the call, check what the panel can support, and run the circuit to where the equipment lives, whether that is a garage, a barn, or a basement workshop.
An outdoor outlet that is not properly rated for weather exposure becomes a problem over time, particularly in a region where freeze-thaw cycles and wet winters put stress on anything exposed to the elements. We install weatherproof receptacles and in-use covers at exterior locations, run the circuit from a protected source inside, and make sure the GFCI protection is correct for an outdoor location. Landscape lighting circuits, security lighting, and power for outbuildings follow the same approach.
Low-voltage work sits alongside the electrical rough-in on most renovation projects. Doorbell wiring, data drops, and the rough-in for structured wiring all need to be planned alongside the circuit layout so the walls are not opened twice. We handle the low-voltage side as part of a broader wiring project, or as a standalone call when the existing doorbell or data wiring has failed.
Most electrical work beyond a simple device replacement requires a permit and an inspection. The permit is filed before the work starts, the inspection happens after, and the sequence matters because an inspector needs to see the wiring before the walls close. We handle the permit filing as part of the job so the paperwork does not become something the homeowner has to chase.
The rules vary depending on the jurisdiction and the type of work. Panel upgrades, new circuits, and service-entrance work are the jobs most consistently subject to inspection requirements. Outlet and switch replacements in an existing location are often exempt, but that depends on the scope and the local authority. We confirm what applies to your specific job before the visit is scheduled, so the inspection timeline is built into the plan from the start.
We are available every day from 8:00 AM to 8:30 PM. When you call, the conversation covers the scope of the job, the price, and what time works. Nothing is scheduled without the price being confirmed first, and the scope is settled on the call so there are no gaps when we arrive.
Some electrical problems are not convenient. A breaker that will not reset, an outlet that is sparking, a panel that smells like it is overheating - these are not situations where a week's wait is reasonable. We take short-notice work and answer calls about urgent situations during our hours. One call and we are on it.
For rental units, businesses, and commercial spaces in Exeter that cannot simply go dark for a day, we work through the job sequence on the call so the visit is planned around what the property needs. That might mean staging the work across the panel to keep certain circuits live, or scheduling the visit around a tenant's hours. The scope is worked out before anyone shows up.
Electrical rough-in has to happen at the right point in a renovation sequence. The framing needs to be up and the insulation needs to be out before circuits are run, but the walls need to stay open until the inspection is done. If drywall goes up before the inspector signs off, the walls come back down. Getting the electrician on site at the right time prevents that.
The same logic applies when a panel upgrade is part of a larger project. If the renovation adds load, the panel question belongs at the start of the planning conversation, not at the end when the new circuits are already roughed in and the panel turns out to be full. We cover the capacity question on the call so the project does not hit that wall mid-build. A load calculation is part of how that conversation goes, and it shapes the scope before any work is priced.
The line between what we fix and what belongs to the utility runs at the meter. Everything from the meter into the panel and through the branch circuits is our side. The service entrance, the meter base, and the lines coming in from the street belong to the utility. That boundary matters when a fault is hard to locate, because the fix depends entirely on which side of the meter the problem sits.
When we diagnose a fault, part of the process is ruling out the utility's side. If the voltage at the panel is unstable, if one leg of the service is reading low, or if the problem disappears and returns in a pattern that tracks with the grid rather than with the home's circuits, those are signs the utility needs to be involved. We identify that on the call or during the visit, and we tell you directly what the next step is. If it is a utility issue, you get a straight answer and the information you need to report it. What a job like this usually involves is described on our electrical services page.
The price for any electrical job is arrived at by understanding the scope. A panel upgrade is priced differently depending on the current service level, what the load calculation shows, and whether the service entrance needs work at the same time. A wiring repair depends on what the fault turns out to be and what has to be opened up to reach it. A new circuit is priced based on the run length, the panel's available capacity, and what the circuit needs to carry.
None of those numbers can be settled before the job is scoped, which is why the price is confirmed on the call rather than posted as a flat rate. What you get when you call is a real conversation about the job, a price that reflects what it actually involves, and a clear answer on what that price covers. Ask what it covers and you get a straight answer.
Call (603) 556-8248 to get the rate for your specific job.
We cover Exeter and the surrounding towns throughout Rockingham County. That includes Kensington, Stratham, Newfields, East Kingston, and Hampton Falls. Whether the property is in Exeter itself or in one of the neighboring communities, the call works the same way: scope the job, confirm the price, schedule the visit.
Rockingham County has a mix of property types and ages, and the electrical work that comes out of that range is what we cover.
Call (603) 556-8248 and we will take it from there.
Older homes in a town like Exeter tend to surface a predictable set of issues: panels that were sized for lighter loads than the home now carries, branch circuits that have been extended or modified without documentation, and wiring that has reached the end of its useful life. GFCI and AFCI protection is also commonly missing in locations where it is now required. A safety inspection covers all of those areas and gives a clear picture of where the system stands before any repair work is prioritized.
The wiring itself can be corrected. Whether a permit is required for the remedial work depends on the scope and on what the local inspection process requires. We do the repair or replacement work and can describe what was done. Questions about permit requirements for a specific address are best confirmed with the relevant authority.
Yes, where the wiring condition allows it. A phased rewire addresses the most urgent sections first and leaves the rest for later visits. The practical constraint is that some sections of older wiring affect others, so the sequence matters. We assess the property and discuss what a phased approach would look like before committing to a plan.
Not always. A panel can be replaced with one of the same service rating if the service entrance and the meter are in good condition and the load calculation supports it. A service upgrade, which increases the amperage coming into the building, is a separate decision that depends on the actual load and what the property needs. We assess both on the visit.
Meters and panels are sometimes located in a shared utility room, on an exterior wall, or in a building common area. Call and describe where the panel is and we will tell you what access is needed for the visit. For panels in shared or restricted areas, access coordination is part of the booking conversation.
Yes. We cover Exeter and the surrounding communities, including Stratham, Kensington, Newfields, East Kingston, and Hampton Falls. The call works the same way regardless of which town the property is in.
Call (603) 556-8248 and we will confirm coverage for your address and scope the job from there.
Yes, and that is how most jobs start. When you call, we go through what the job involves, ask about the symptom or the scope, and give you the rate before anything is scheduled. The price is confirmed on the call so you know what the visit covers before it happens.
A hot tub requires a dedicated 240-volt circuit, a disconnect within sight of the unit, and GFCI protection at the circuit. We handle the wiring from the panel to the disconnect and to the connection point at the tub. The panel's available capacity is checked before the circuit is run, and a load calculation confirms the service can carry the added demand.
Electrical faults do not improve on their own. A breaker that trips once will trip again. A panel that is running at capacity has nowhere to go when the next load is added. The right time to call is before the situation forces the call.
We are available every day from 8:00 AM to 8:30 PM.
Call (603) 556-8248 for a quote on any electrical work in Exeter.
The scope and the price are settled on the call, and we can often get out sooner than people expect.
Close by, we also take electrical work in: Stratham, Hampton, Newmarket, Haverhill, Methuen.
Check our town-by-town list.
From a tripped breaker to a full panel replacement, we handle the electrical work that keeps homes and businesses in Exeter running safely. The table below covers what each service includes, who it fits best, and what is practical to know before you call. If a job does not fit neatly into one category, call us and we will scope it on the phone.
| Service | What's Included | Best For | Good to Know |
|---|---|---|---|
| Backup Generator Installation | Transfer switch installationDedicated generator circuitPanel integration for priority circuitsLoad scoping on the call | Exeter and Rockingham County homeowners who lose power during nor'easters and ice storms and need heat, lights, and refrigeration to stay on | A transfer switch is required by code for permanent generator hookups. It isolates the generator from the utility grid, which protects utility workers during an outage. |
| Electrical Panel & Service Upgrades | Panel replacement and load calculationsService entrance upgrades to 200-ampDual-wire breaker terminal and corrosion remediationCapacity assessment for added circuits | Older homes with undersized panels, properties adding EV chargers or generators, and commercial clients needing more capacity | Panel work in New Hampshire typically requires a permit and inspection. We handle that process as part of the job so the work is documented and compliant when it is done. |
| Electrical Safety Inspections | Pre-purchase wiring and panel reviewLandlord compliance inspectionsCode concern identificationWritten findings after the visit | Homebuyers, landlords preparing a unit for a new tenant, and property managers documenting electrical conditions | An inspection before a sale closes or a lease starts gives both parties a clear record of the system's condition. That documentation is useful if questions come up later. |
Call (603) 556-8248 to get a quote, confirm the scope, and find out what the work involves for your specific property.
(603) 556-8248